01 / 20

Extraction &
Distillation

Master the MCAT fundamentals of liquid-liquid extraction and distillation: partition coefficients, Raoult's law, and how to separate mixtures based on polarity and boiling point.

MCAT Chem/Phys

Why Separation Matters

In chemistry and biology, mixtures are everywhere: blood contains thousands of dissolved solutes, reaction flasks hold products alongside byproducts. Separation techniques exploit differences in physical properties to isolate desired compounds without breaking chemical bonds.

Extraction
Separates based on differential solubility between two immiscible solvents
Distillation
Separates based on differences in boiling point (vapor pressure)

Liquid-Liquid Extraction

A solute distributes between two immiscible liquids (e.g., water and dichloromethane). The solute preferentially dissolves in the solvent where it is more soluble. The ratio at equilibrium is described by the partition coefficient.

Organic Layer Aqueous Layer Interface Separatory Funnel

The Partition Coefficient \( K_D \)

At equilibrium, the ratio of concentrations of a solute in two immiscible solvents is constant at a given temperature. This is the partition coefficient (or distribution coefficient):

A large \( K_D \) means the solute favors the organic phase. A small \( K_D \) means it prefers the aqueous phase. This value is independent of the total amount of solute: it depends only on temperature and the solvent system.

Multiple Extractions: More Efficient

Performing several small-volume extractions is always more efficient than one large-volume extraction. The fraction remaining in the aqueous phase after \( n \) extractions is:

Introduction to Distillation

Distillation separates components of a liquid mixture by exploiting differences in boiling points. When a mixture is heated, the component with the higher vapor pressure (lower boiling point) vaporizes preferentially and is collected upon condensation.

Vapor Pressure
Pressure exerted by a vapor in equilibrium with its liquid. Higher vapor pressure means easier evaporation.
Boiling Point
Temperature at which vapor pressure equals atmospheric pressure. Lower BP = more volatile.

Raoult's Law and Ideal Solutions

For an ideal solution, the partial vapor pressure of each component is proportional to its mole fraction in the liquid phase:

Where \( P_A \) is the partial vapor pressure of component A, \( \chi_A \) is its mole fraction in the liquid, and \( P_A^\circ \) is the vapor pressure of pure A. The total pressure is:

Types of Distillation

Simple
Single vaporization-condensation cycle. Works when BP difference is > 25 °C.
Fractional
Uses a fractionating column for multiple vaporization cycles. For BP differences < 25 °C.
Vacuum
Reduces external pressure to lower effective BP. For thermally sensitive compounds.

Distillation Apparatus

Boiling Flask Heat Fractionating Column Thermometer Condenser H₂O in H₂O out Distillate

Extraction vs. Distillation

Extraction Distillation
Separates by Solubility / Polarity Boiling Point / Vapor Pressure
Key equation \( K_D = \frac{[S]_{org}}{[S]_{aq}} \) \( P_A = \chi_A P_A^\circ \)
Equipment Separatory funnel Boiling flask, condenser
Best for Immiscible liquid pairs Miscible liquids, different BPs
Efficiency boost Multiple small extractions Fractionating column

Step-by-Step: Extraction Problems

1
Identify the two phases. Which solvents are present? Which is denser? (Aqueous is usually the lower layer, unless the organic solvent is denser, e.g., DCM.)
2
Determine solute preference. Use "like dissolves like": polar/ionic solutes favor aqueous; nonpolar solutes favor organic.
3
Apply \( K_D \). Set up the partition coefficient. A large \( K_D \) means more solute in the organic layer.
4
Consider multiple washes. Use the formula \( q_n = \left(\frac{V_{aq}}{V_{aq} + K_D V_{org}}\right)^n \) to calculate remaining solute.

Step-by-Step: Distillation Problems

1
Compare boiling points. The component with the lower BP has the higher vapor pressure and distills first.
2
Apply Raoult's law. Calculate partial pressures: \( P_A = \chi_A \cdot P_A^\circ \). The vapor is enriched in the more volatile component.
3
Determine vapor composition. Use \( y_A = \frac{P_A}{P_{total}} \). The mole fraction in the vapor phase tells you what is collected.
4
Choose the right method. Simple distillation for large BP gaps; fractional for small gaps; vacuum for heat-sensitive compounds.

Example 1: Single Extraction

A solute has \( K_D = 4.0 \) between diethyl ether and water. You have 100 mL of aqueous solution and extract once with 100 mL of ether. What fraction remains in water?

Example 2: Multiple Extractions

Same solute (\( K_D = 4.0 \)), same 100 mL aqueous solution, but now you use two 50 mL portions of ether instead. What fraction remains?

Example 3: Raoult's Law Calculation

A mixture contains 0.60 mol fraction benzene (\( P^\circ = 100 \) mmHg) and 0.40 mol fraction toluene (\( P^\circ = 40 \) mmHg). Find the total vapor pressure and the vapor composition.

Common Mistakes

✕ Inverting \( K_D \)
Confusing which phase is in the numerator. By convention, organic over aqueous unless stated otherwise.
✕ One Big Wash
Using all solvent in a single extraction instead of multiple portions. Multiple washes are always more efficient.
✕ Wrong Layer
Assuming the organic layer is always on top. Dense solvents like DCM (\( \rho = 1.33 \)) sink below water.

Question 1 of 5

A compound has a partition coefficient \( K_D = 3.0 \) between ethyl acetate and water. If 90 mL of aqueous solution is extracted once with 90 mL of ethyl acetate, what percentage of the compound remains in the aqueous layer?

Question 2 of 5

Which separation technique would be most appropriate for isolating a heat-sensitive compound from a mixture with a similar boiling point?

Question 3 of 5

According to Raoult's law, a solution of 0.30 mol fraction acetone (\( P^\circ = 230 \) mmHg) and 0.70 mol fraction water (\( P^\circ = 24 \) mmHg) has a total vapor pressure of:

Question 4 of 5

During distillation, the first fraction collected will be enriched in the component with:

Question 5 of 5

Why are multiple small extractions more efficient than a single large-volume extraction?