01 / 20

Weight Painting
in Blender

Learn how to edit vertex weights to achieve clean, natural deformations when bones move your mesh.

Blender 3D Rigging

What Is Weight Painting?

Weight painting is the process of assigning influence values to each vertex of a mesh, telling Blender how much a specific bone should move that vertex. Each vertex stores a weight between \(0.0\) (no influence) and \(1.0\) (full influence).

0.0 0.5 1.0 Weight Spectrum Upper Arm Bone Forearm Bone Colored vertices show bone influence

Why Weight Painting Matters

When you parent a mesh to an armature using Automatic Weights, Blender guesses how each bone should influence nearby vertices. These guesses are often imperfect: elbows collapse, shoulders tear, and fingers drag unrelated geometry.

✕ Bad Weights
Mesh collapses at joints, vertices stretch unnaturally, geometry clips through itself.
✓ Good Weights
Smooth bending at joints, volume preservation, natural deformation in every pose.

Vertex Groups and Bones

Every bone in an armature has a corresponding vertex group on the mesh. The vertex group stores the weight value for each vertex. When you paint in Weight Paint mode, you are editing these group values.

Armature Spine L.Arm R.Arm Vertex Groups Spine L.Arm R.Arm Each group stores per-vertex weights

The Normalization Rule

For clean deformations, the weights of all bones influencing a single vertex should sum to \(1.0\). This is called normalization. If a vertex has weights from two bones:

✓ Normalized V Bone A 0.7 Bone B 0.3 ✕ Not Normalized V Bone A 0.8 Bone B 0.6

Understanding Weight Values

\( w = 0.0 \)
No influence Vertex stays stationary
\( w = 0.5 \)
Half influence Vertex moves 50% with bone
\( w = 1.0 \)
Full influence Vertex moves 100% with bone

Brush Blend Modes Compared

The Weight Paint brush has several blend modes that determine how strokes affect existing weights. Understanding these is essential for precision work.

Mix Add Subtract
Behavior Replaces weight toward brush value Increases weight by brush strength Decreases weight by brush strength
Best For Setting exact values Building up influence Removing stray influence
Risk Overwriting nearby weights Exceeding \(1.0\) without normalize Going below \(0.0\) (clamped)
Typical Strength \(0.5\) to \(1.0\) \(0.05\) to \(0.2\) \(0.05\) to \(0.2\)

Step-by-Step Workflow

1
Select your mesh and switch to Weight Paint mode (Ctrl+Tab or the mode dropdown).
2
Select the bone to edit: hold Ctrl and click a bone in the viewport. The active vertex group updates automatically.
3
Enable Auto Normalize in the Tool sidebar (N panel > Tool > Options) to keep weights summing to \(1.0\).
4
Paint with low strength (\(0.1\) to \(0.3\)) and build up gradually. Switch between Add and Subtract blend modes.
5
Test your pose frequently: select the armature, enter Pose mode, and rotate the bone to check deformation.
6
Clean up: use Weights > Clean (removes tiny values below a threshold) and Weights > Smooth to blend transitions.

Example: Fixing an Elbow

The elbow is the most common problem area. After auto-weights, the forearm bone often bleeds influence into the upper arm, causing a crease or candy-wrapper twist when bent.

Before Pinch! After Smooth!

Example: Shoulder Cleanup

Shoulders are tricky because they involve multiple overlapping bone influences: the upper arm, the shoulder bone, and the spine. Automatic weights often leave messy transitions.

1
Identify the problem: Rotate the upper arm bone forward. If the chest deforms, the upper arm has too much influence on the torso.
2
Select the upper arm bone (Ctrl+Click). Switch brush to Subtract, strength \(0.15\).
3
Paint away the stray influence on the chest and back. With Auto Normalize on, this weight automatically transfers to the spine bone.
4
Smooth the transition: Use Weights > Smooth or the Blur brush (Shift+click) along the shoulder crease for a natural gradient.

Advanced: Vertex Masking

For precise control, enable Vertex Selection Masking (the cube icon in the header bar). This lets you first select specific vertices, then paint only those vertices.

Vertex Selection Masking Only selected (purple) vertices are paintable

Essential Brush Settings

Weight
The target value the brush paints toward (for Mix mode). Set to \(1.0\) for full influence, \(0.0\) to erase.
Strength
How quickly the brush reaches the target weight. Low values (\(0.05\) to \(0.2\)) give more control.
Radius
Brush size in pixels. Use F key to resize interactively. Smaller is more precise.
Falloff
The curve controlling how influence drops off from center to edge. Smooth falloff prevents hard edges.

Smoothing Weight Transitions

Hard weight transitions create visible creases in the mesh. Blender provides two smoothing methods to create natural gradients between bone influences:

Blur Brush
Hold Shift while painting to temporarily switch to the Blur brush. Averages weights of nearby vertices. Best for local touch-ups.
Smooth Weights
Menu: Weights > Smooth. Applies a global smoothing pass across the entire vertex group. Useful after major edits.
Sharp Transition Smooth Gradient

Common Mistakes

✕ Painting at Full Strength
Using brush strength \(1.0\) creates harsh, all-or-nothing weights. Always use \(0.05\) to \(0.3\) and build up gradually.
✕ Forgetting Auto Normalize
Without normalization, weights can exceed \(1.0\), causing vertices to fly off or double-transform unpredictably.
✕ Not Testing Poses
Painting only in rest pose hides problems. Always rotate bones to extreme angles to reveal hidden weight issues.

Quick Reference Summary

Task Tool / Setting Shortcut
Enter Weight Paint Mode Mode dropdown or Ctrl+Tab Ctrl+Tab
Select bone to paint Ctrl+Click bone Ctrl+LMB
Resize brush F key + drag F
Blur/Smooth Shift+Click to blur Shift+LMB
Clean tiny weights Weights > Clean Menu
Global smooth Weights > Smooth Menu
Toggle normalize Tool sidebar > Options N panel

Question 1 of 5

A vertex has weights of \(0.6\) from Bone A and \(0.4\) from Bone B. When Bone A moves, how far does the vertex follow Bone A's transformation?

Question 2 of 5

What does Auto Normalize do when you paint weights on a vertex that already has influence from multiple bones?

Question 3 of 5

You rotate the forearm bone and notice the chest mesh deforms slightly. What is the most likely cause?

Question 4 of 5

Which brush blend mode is best for gradually building up bone influence on a vertex that currently has a weight of \(0.0\)?

Question 5 of 5

What is the purpose of enabling Vertex Selection Masking in Weight Paint mode?