01 / 22

Walls in
Autodesk Revit

Master the fundamentals of creating and editing walls: understand wall types, constraints, and joins to build accurate architectural models.

Autodesk Revit

What Is a Wall in Revit?

A wall in Revit is a system family element that represents a vertical building component. Unlike loadable families (like furniture), walls are defined by layers of materials stacked from the exterior face to the interior face.

Exterior Interior Brick Air Gap Insulation Structure Gypsum Total Wall Thickness

Three Categories of Walls

Basic Wall
The most common type. Made of multiple layers (structure, insulation, finish). Used for exterior and interior partitions.
Curtain Wall
A non-structural facade composed of panels and mullions. Ideal for glass storefronts, atriums, and modern facades.
Stacked Wall
Combines multiple basic wall types vertically. Use when the wall composition changes at different heights (e.g., brick below, siding above).

Why Walls Matter in BIM

In a Building Information Model, walls are not just lines on a drawing. They carry intelligent data: material quantities, fire ratings, acoustic values, and cost information. Every wall you place affects schedules, sections, and 3D views automatically.

Automatic Scheduling
Wall areas, volumes, and materials appear in schedules instantly.
Section Accuracy
Cut sections show each layer: structure, insulation, and finish.
Coordination
Structural, MEP, and architectural teams reference the same wall data.

Core Wall Properties

Every wall instance in Revit is controlled by two sets of properties: Type Properties (shared by all walls of that type) and Instance Properties (unique to a single wall placement).

Type Properties
Structure (layers), wrapping, coarse-scale fill, default thickness, function (exterior, interior, etc.)
Instance Properties
Base Constraint, Top Constraint, Base Offset, Top Offset, Unconnected Height, Location Line

Wall Constraints Explained

Level 1 (Base Constraint) Level 2 (Top Constraint) Wall Base Offset Top Offset Unconnected Height Used when Top Constraint = "Unconnected"

The Location Line

The Location Line determines which part of the wall aligns with the line you draw. This is critical for accurate dimensioning and room sizing.

Finish Face (Exterior) Core Centerline Wall Centerline Finish Face (Interior) Location Line Options:

Type vs Instance Properties

Type Properties Instance Properties
Scope All walls of that type Single wall only
Access Edit Type button Properties palette
Examples Structure, layers, thickness Base/Top Constraint, offsets
Change impact Global: all instances update Local: one wall updates
When to duplicate Need a new composition N/A: just modify values

How to Place a Wall

1
Go to Architecture tab → Wall. Click the Wall button in the Build panel (shortcut: WA).
2
Select a wall type from the Type Selector dropdown in the Properties palette.
3
Set constraints in the Options Bar: Height (Level 2 or Unconnected), Location Line, Chain option.
4
Draw the wall. Click start point, then endpoint. Use Line, Rectangle, Circle, or Pick Lines draw mode.
5
Press Esc or Modify to finish. Select the wall to verify its Instance Properties in the palette.

Understanding Wall Joins

When two walls meet, Revit automatically joins them. The join type controls how layers clean up at the intersection. You can override joins using the Wall Joins tool.

Butt One wall stops at the other's face Miter Layers meet at a diagonal seam Square Off One wall is squared off, the other butts

Join Display and Cleanup

Revit's automatic cleanup depends on wall Function and layer priority. Layers with the same function and priority merge cleanly; mismatched layers show visible lines at the joint.

1
Layer Function matters: Structure merges with Structure, Finish merges with Finish. Layers of different function never merge.
2
Layer Priority (1-5) determines cleanup at joins. Higher priority layers (like Structure [1]) will cut through lower priority layers (like Finish [4]).
3
Wrapping at Inserts/Ends: set in the Type Properties to control whether finish layers wrap around wall ends and openings.

Editing Wall Structure

To modify the layers of a wall type, open the Edit Assembly dialog. Here you can add, remove, or reorder layers and set the Core Boundary lines.

Edit Assembly Dialog Function Material Thickness Wraps Core Boundary Finish 1 Brick 90 mm ✓ Membrane Air Barrier 0 mm - Structure Concrete 200 mm - Finish 2 Gypsum 16 mm ✓ Total: 306 mm

Example 1: Simple Exterior Wall

Create an exterior wall for a residential project: Brick finish, concrete block structure, and gypsum interior finish.

1
Architecture → Wall → WA. In the Type Selector, pick "Basic Wall: Generic - 200mm".
2
Duplicate the type. Rename it "Exterior - Brick/Block/Gyp".
3
Edit Structure. Set Finish 1 = Brick (90mm), Structure = Concrete Block (190mm), Finish 2 = Gypsum (16mm).
4
Set constraints: Base = Level 1, Top = Level 2, Location Line = Finish Face: Exterior.
5
Draw the wall perimeter. Check the 3D view to confirm layers and height.

Example 2: Interior Partition with Offset

Place a lightweight partition that stops 300 mm below the ceiling for a suspended ceiling gap.

Level 1 Level 2 Partition Top Offset: -300 mm Suspended Ceiling Zone

Example 3: Fixing a Bad Join

Two exterior walls meet at a corner, but the layers are not cleaning up. The brick on one wall overlaps the gypsum on the other.

1
Verify base constraints. Both walls must share the same Base Constraint level. If one is on Level 1 and the other on Level 0, they will not join.
2
Check wall types. Open Edit Assembly for each. Ensure the Structure layer has the same Function (Structure [1]) so they recognize each other.
3
Use the Wall Joins tool. Click the join and cycle through Butt, Miter, or Square Off until the layers display correctly.
4
Right-click → Disallow Join if you intentionally want walls to remain separate (e.g., at an expansion joint).

Common Mistakes

✕ Editing Type Without Duplicating
Modifying a wall type's structure changes every instance in the project. Always Duplicate first.
✕ Wrong Location Line
Drawing walls on "Wall Centerline" when dimensions reference the exterior face leads to inaccurate room sizes.
✕ Mismatched Constraints
Walls on different base levels or with different top constraints will not join cleanly, even if they touch in plan view.
✕ Ignoring Layer Priority
Layers with mismatched priorities cause visible lines at joins. Check priority numbers in Edit Assembly for consistent cleanup.

Summary of Wall Concepts

Concept What It Controls Where to Set It
Wall Type Layer composition, thickness Type Selector / Edit Type
Base Constraint Which level the wall starts from Instance Properties
Top Constraint Which level (or height) the wall extends to Instance Properties
Location Line Which face/center aligns with the drawn line Options Bar / Instance
Wall Join How layers meet at corners Wall Joins tool
Wrapping Whether finish layers wrap at openings/ends Edit Assembly (Type)

Question 1 of 5

In Revit, walls are classified as a system family. What does this mean in practice?

Question 2 of 5

You need to place an exterior wall so that dimensions reference the outside face of the brick. Which Location Line should you choose?

Question 3 of 5

Two walls of the same type meet at a corner but their layers are not cleaning up. Which is the most likely cause?

Question 4 of 5

You want a partition wall to stop 300 mm below Level 2 to allow space for a suspended ceiling. How should you configure the wall?

Question 5 of 5

What happens if you change the Structure (layer composition) of a wall type without duplicating it first?