01 / 22

Stairs, Ramps
& Railings

Master vertical circulation in Autodesk Revit: place stairs, configure ramps, and attach railings to connect every level of your building model.

Autodesk Revit

What Is Vertical Circulation?

In architecture, vertical circulation refers to any element that moves people between different floor levels. The three primary components in Revit are stairs, ramps, and railings.

Stairs
A series of steps connecting two levels, defined by risers and treads.
Ramps
An inclined surface providing accessible passage between levels, governed by slope limits.
Railings
Protective barriers attached to stairs, ramps, or floor edges for safety and code compliance.

Why Stairs & Ramps Matter

Every multi-storey Revit model needs vertical circulation. Without it, floors are disconnected islands. Properly configured stairs and ramps also ensure your model meets building codes and accessibility standards.

Anatomy of a Stair

Riser Tread Level Height Top Level Base Level Nosing

Key Stair Formulas

Revit uses the level-to-level height and your target riser height to compute the number of risers automatically. The core relationships are:

Number of Risers
\( n = \dfrac{\text{Level Height}}{\text{Riser Height}} \)
Number of Treads
\( \text{Treads} = n - 1 \) (one fewer tread than risers)

Ramp Basics & Slope Rule

Rise Run
\( \text{Slope} = \frac{\text{Rise}}{\text{Run}} \)
ADA Max: \( 1 : 12 \)

Stairs vs. Ramps

Stairs Ramps
Shape Stepped treads & risers Continuous inclined surface
Slope Steep (varies by code) Max \( 1 : 12 \) (ADA)
Footprint Compact Much larger for same rise
Accessibility Not wheelchair accessible Wheelchair accessible
Revit Tool Path Architecture → Stair Architecture → Ramp

How to Place a Stair

1
Open the tool: Architecture tab → Circulation panel → Stair.
2
Set levels: In the Properties panel, confirm Base Level and Top Level. Revit calculates risers automatically.
3
Choose a type: Select Stair by Component (runs + landings) or Stair by Sketch for custom shapes.
4
Click to draw: Click the start point, then click the end of each run. Revit shows a green counter of remaining risers.
5
Finish: Click the green check (✓) when the counter reaches 0 Risers Remaining.

Component vs. Sketch Mode

Stair by Component
Pre-built runs and landings snap together. Faster for straight, L-shaped, and U-shaped stairs. Best for standard designs.
Stair by Sketch
Draw boundary and riser lines freely. Required for spiral, curved, or irregular stair geometries. More manual control.

Example: L-Shaped Stair

Run 1 Landing Run 2 UP UP

Placing a Ramp

1
Open the tool: Architecture tab → Circulation panel → Ramp.
2
Set levels & slope: Confirm Base/Top Level. Check Maximum Incline Length and Slope in Type Properties (default is \( 1 : 12 \)).
3
Draw the path: Click start point, then end point. Revit auto-calculates length from the slope ratio.
4
Add landings: For long ramps, click intermediate points. ADA requires a landing every 9000 mm (30 ft) of run.
5
Finish: Click the green check (✓). Railings are added automatically by default.

Attaching Railings

Railings in Revit can be placed in three ways. The method you choose depends on the host element:

Auto-Hosted
Railings appear automatically on new stairs and ramps. Controlled via the stair/ramp Type Properties.
Place on Host
Architecture → Railing → Place on Host. Hover over a stair or ramp and click to attach.
Sketch Path
Architecture → Railing → Sketch Path. Draw lines along floor edges, balconies, or anywhere a railing is needed.

Railing Type Properties

Top Rail Balusters Posts Height

Example: U-Shaped Stair

Run 1 Run 2 Landing UP UP Gap

Example: Ramp with Landings

Run 1 Landing Run 2 Landing Run 3 Direction of travel

Common Mistakes

✕ Wrong Top Level
Forgetting to set the correct Top Level causes Revit to create too many or too few risers. Always verify both levels before drawing.
✕ Ignoring Riser Warnings
Revit flags yellow/red warnings when risers exceed code limits. Dismissing these leads to non-compliant designs.
✕ Ramp Slope Too Steep
Setting a slope steeper than \( 1 : 12 \) without intentionally overriding accessibility requirements violates ADA guidelines.
✕ Deleting Auto-Railings
Removing automatically placed railings and forgetting to replace them results in missing safety elements in the model and documentation.

Quick Reference Summary

Property Stairs Ramps Railings
Revit Tab Architecture → Stair Architecture → Ramp Architecture → Railing
Key Parameter Riser / Tread size Slope (\( 1 : 12 \)) Height / Baluster spacing
Modes Component / Sketch Sketch only Host / Sketch Path
Auto-Railings Yes (default) Yes (default) N/A
Common Code Max riser 178 mm Max slope \( 1 : 12 \) Min height 1070 mm

Question 1 of 5

If a building has a floor-to-floor height of 3500 mm and the target riser height is 175 mm, how many risers will Revit calculate?

Question 2 of 5

What is the maximum slope for an ADA-compliant ramp in Revit?

Question 3 of 5

Which stair creation mode should you use for a spiral staircase in Revit?

Question 4 of 5

If a stair has 20 risers, how many treads does it have?

Question 5 of 5

Which method lets you add a railing along a floor edge that has no stair or ramp?