01 / 21

Ceilings in
Autodesk Revit

Learn to create, modify, and control ceiling elements in Revit: from automatic sketch boundaries to compound ceiling types and height offsets.

Autodesk Revit

What Is a Ceiling in Revit?

A ceiling is a system family element in Revit that represents the underside surface of a room. Unlike floors, which sit at the bottom of a level, ceilings are placed looking up from below. Revit uses a special Reflected Ceiling Plan (RCP) view to display them: imagine lying on the floor and looking straight up.

The Reflected Ceiling Plan

Floor Plan View Floor Ceiling (not visible) ↓ Looking down RCP View Ceiling Visible ↑ Looking up

Why Ceilings Matter in BIM

Room Volume
Revit uses ceilings to calculate accurate room volumes and areas for energy analysis and scheduling.
MEP Coordination
Lighting fixtures, diffusers, sprinklers, and speakers are hosted by ceilings: their placement depends on the ceiling being modeled correctly.
Documentation
Ceiling plans, finish schedules, and material takeoffs all draw data directly from ceiling elements in the model.

Automatic vs. Sketch Ceiling

Automatic Ceiling Click inside room Revit detects walls and fills automatically vs Sketch Ceiling You draw custom boundary lines in sketch mode

The Ceiling Placement Rule

Level 1 Floor Ceiling
\(8'~0''\)
Height Offset

Ceiling Types in Revit

Ceiling Types Basic Ceiling Compound GWB on Mtl. Stud Single layer Generic or ACT
\(2' \times 2'\) or \(2' \times 4'\)
Multiple layers Structure + Finish Edit in Type Props Gypsum + Framing Drywall on studs Flat, no grid Edit Type > Structure > Edit to modify layers

Ceiling vs. Floor: Key Differences

Ceiling Floor
View Type Reflected Ceiling Plan Floor Plan
Default Offset \(8'~0''\) above level \(0'~0''\) at level
Perspective Looking up Looking down
Category Ceilings Floors
Hosts Light fixtures, diffusers Furniture, plumbing
Sketch Tool Automatic or Sketch Sketch only

How to Place a Ceiling

1
Open an RCP view. Go to the Project Browser and expand "Ceiling Plans". Double-click the correct level.
2
Architecture tab > Ceiling. Select the Ceiling tool from the Build panel on the Architecture ribbon.
3
Choose a ceiling type. Use the Type Selector in the Properties panel to pick the desired type (e.g., "\(2' \times 4'\) ACT System").
4
Automatic or Sketch. For Automatic: hover inside the room and click. For Sketch: click "Sketch Ceiling" and draw boundary lines, then click the green checkmark to finish.
5
Set Height Offset. In Properties, adjust "Height Offset From Level" if the ceiling is not at the default \(8'~0''\).

Example 1: Automatic Ceiling

Office 101 Click here
\(15'~0''\)
Properties Type:
\(2' \times 4'\) ACT System
Height Offset:
\(8'~0''\)
Room Bounding: Yes

Example 2: Sketch Ceiling with Bulkhead

Section View: Lobby L1
Ceiling @ \(10'\)
Ceiling @ \(10'\)
Bulkhead @ \(8'\)
\(10'\)
\(8'\)

Example 3: Modifying an Existing Ceiling

1
Select the ceiling by clicking on it in the RCP view. The boundary highlights in blue.
2
Edit Boundary: Click "Edit Boundary" in the Modify ribbon to re-enter sketch mode. You can add, remove, or reshape boundary lines.
3
Change Type: Use the Type Selector to switch from "\(2' \times 4'\) ACT" to "GWB on Mtl. Stud" or another type.
4
Adjust Height: In Properties, change Height Offset From Level to raise or lower the ceiling.
5
Finish Edit: Click the green checkmark to apply changes. Hosted elements (lights, diffusers) move automatically with the ceiling.

Key Properties of Ceilings

Height Offset
Distance above the host level. Positive values raise the ceiling; negative values lower it below the level (rare).
Room Bounding
When set to "Yes", the ceiling defines the top boundary of a room, affecting volume calculations.
Slope
Add a slope arrow in sketch mode to create a sloped ceiling. Define the head and tail heights.

Compound Structure Layers

Ceiling Cross-Section (GWB on Mtl. Stud)
Finish 1: Gypsum Wall Board (\(\frac{5}{8}''\))
Structure: Metal Stud (\(3 \frac{5}{8}''\))
Air Space (optional) Substrate: Insulation (varies) Total Thickness Edit Type > Structure > Edit to add/remove layers Each layer has: Function, Material, Thickness

Common Mistakes

✕ Wrong View
Trying to place a ceiling in a Floor Plan view instead of a Reflected Ceiling Plan. The tool won't appear or won't work correctly.
✕ Open Boundary
Leaving gaps in sketch-mode boundary lines. Revit requires a fully closed loop to create the ceiling.
✕ Overlapping Ceilings
Creating two ceiling elements at the same height in the same space. This causes volume errors and duplicate schedules.

Ceiling Methods Summary

Automatic Sketch
Speed Fast: one click Slower: draw boundary
Shape Matches room walls Any custom shape
Use Case Standard rectangular rooms Irregular rooms, bulkheads, soffits
Grid Alignment Auto-centered User-controlled
Edit Boundary Re-enter sketch mode Already in sketch mode
Slope Support No (must convert to sketch) Yes: add slope arrow

Question 1 of 5

In which view type must you be working to place a ceiling in Revit?

Question 2 of 5

What is the default Height Offset From Level for a newly placed ceiling in Revit?

Question 3 of 5

You need to create an L-shaped ceiling that does not follow the room walls exactly. Which placement method should you use?

Question 4 of 5

What happens if you leave a gap in the boundary lines when using Sketch Ceiling mode?

Question 5 of 5

Which property must be set to "Yes" for a ceiling to affect room volume calculations?