01 / 21

Variables &
Controls

Master how scientists design experiments by understanding independent, dependent, and controlled variables: the foundation of every ACT Science passage.

ACT Science

What Is a Variable?

A variable is any factor, trait, or condition that can change or be changed in an experiment. Scientific experiments are built around the question: what happens when we change one thing and measure another?

On the ACT Science section, almost every Research Summaries and Conflicting Viewpoints passage will test whether you can identify the variables and explain how the experiment was controlled.

The Three Types of Variables

Independent Variable
The factor the scientist deliberately changes between trials. Also called the manipulated variable.
Dependent Variable
The factor that is measured or observed in response to the change. Also called the responding variable.
Controlled Variables
All other factors that are kept the same so they don't affect the results. Also called constants.

Why Controls Matter

Without controlled variables, you can never be sure which change actually caused the result. This is the core idea behind experimental design.

Good Experiment Only 1 thing changed Temperature changed Volume, time: same ✓ Valid conclusion Flawed Experiment Multiple things changed Temperature changed Volume also changed! ✕ Can't tell the cause

The Control Group vs. Experimental Group

Control Group
Receives no treatment or the standard condition. It serves as a baseline for comparison.
Experimental Group
Receives the treatment or change being tested. The independent variable is applied here.

The Golden Rule of Experimental Design

Independent Variable causes Dependent Variable Constant A kept same Constant B kept same Example: Does fertilizer amount affect plant height? IV: Amount of fertilizer DV: Plant height Constants: soil, water, sunlight

Independent vs. Dependent: How to Tell

Independent Variable Dependent Variable
Who decides it? The scientist sets it The experiment reveals it
On a data table Usually the left column or top row Usually the right column(s) or data cells
On a graph Plotted on the x-axis Plotted on the y-axis
Key question "What did they change?" "What did they measure?"
Mnemonic "I" control it "D"ata depends on it

How to Identify Variables on the ACT

1
Read the experimental setup. Find what the scientists deliberately varied between trials or groups.
2
That is the independent variable. It is the "input" being tested: usually the column header on the left side of a data table.
3
Find what was measured or recorded. That is the dependent variable: typically the data values in the table.
4
Everything else stated as "kept the same" or implied by the procedure is a controlled variable.
5
Look for the control group: a trial with no treatment or the baseline condition, used for comparison.

Example 1: Plant Growth Experiment

A student tested how different amounts of sunlight affect plant height. She grew 4 groups of identical seedlings for 30 days, giving each group a different number of hours of light per day. She measured final height in centimeters.

Hours of Light/Day Avg. Height (cm) 2 4.1 6 9.3 10 15.7 14 18.2 ← IV: changed by scientist ← DV: measured result

Example 2: Dissolving Rate Experiment

A chemist investigated whether water temperature affects how quickly sugar dissolves. She added \(5\ \text{g}\) of sugar to \(200\ \text{mL}\) of water at different temperatures and timed how long it took to fully dissolve.

Independent Variable
Water temperature (\(20^\circ\text{C}\), \(40^\circ\text{C}\), \(60^\circ\text{C}\), \(80^\circ\text{C}\))
Dependent Variable
Time to dissolve (seconds)
Controlled Variables
Volume of water (\(200\ \text{mL}\)), mass of sugar (\(5\ \text{g}\)), stirring method, sugar brand

Example 3: Multi-Experiment Passage

ACT passages often describe multiple experiments that share some variables but differ in what they test. You must identify what changes between experiments.

Experiment 1 Varied: temperature Measured: reaction rate
Held constant: \(\text{pH} = 7\), \(10\ \text{mL}\)
Catalyst: none Result: rate increased Experiment 2 Varied: catalyst type Measured: reaction rate
Held constant: \(\text{pH} = 7\), \(10\ \text{mL}\)
Temperature: \(25^\circ\text{C}\) (fixed)
Result: rate depended on type

Reading Data Tables for Variables

On the ACT, data tables are your fastest clue to identifying variables. Follow this pattern:

Column 1 (IV) Column 2 (DV) Column 3 (DV) Value set by scientist Measurement 1 Measurement 2 Next value ... ... This changes across rows = Independent Variable These are measured = Dependent Variable(s)

Variables on Graphs

Temperature (\(^\circ\text{C}\)) : IV
Rate (\(\text{g/min}\)) : DV
20 30 40 50 60 70

Watch Out for Confounding Variables

A confounding variable is an uncontrolled factor that changes along with the independent variable, making it impossible to determine the true cause of the results.

Example
Testing if a new fertilizer helps plant growth, but also moving the experimental group to a sunnier location. Was it the fertilizer or the sunlight?
Fix
Keep all conditions identical except the one being tested. If location changed, it becomes a confounding variable.

Common Mistakes on the ACT

✕ Swapping IV and DV
Saying "plant height is the independent variable" when it was measured, not set by the scientist. Ask: "Did the scientist choose this value?"
✕ Confusing Controls with Control Group
Controlled variables are factors held constant. The control group is a group that receives no treatment. These are different concepts.
✕ Ignoring Confounds
Failing to notice that two things changed between trials. If more than one factor differs, the experiment can't prove which caused the result.

Summary Cheat Sheet

Term Definition How to Spot It
Independent Variable Factor the scientist changes Left column, x-axis, "varied"
Dependent Variable Factor that is measured Right columns, y-axis, "measured"
Controlled Variables Factors kept the same "All other conditions were held constant"
Control Group Group with no treatment "Baseline," "no fertilizer," "0 mg"
Confounding Variable Uncontrolled factor that varies "Also changed," "weakness in design"

Question 1 of 5

In this experiment, what is the independent variable?

Question 2 of 5

A student tested whether the mass of a ball affects how far it rolls down a ramp. She used balls of different masses but kept the ramp angle, surface material, and release height the same. What role do the ramp angle, surface material, and release height play?

Question 3 of 5

Which factor serves as a controlled variable in Experiment 1 but as an independent variable in Experiment 2?

Question 4 of 5

A researcher tested whether a new drug reduces blood pressure. Group A received the drug and Group B received a sugar pill with no active ingredient. Group B is best described as the:

Question 5 of 5

The time of day in this experiment is best described as a: