01 / 21

Understanding
Measurement & Precision

Master the critical skills of reading data accurately, distinguishing precision from accuracy, and interpreting significant figures and uncertainty on the ACT Science section.

ACT Science

What Is Measurement?

In science, a measurement is a quantitative observation that includes both a numerical value and a unit. Every measurement carries some degree of uncertainty because no instrument is perfect.

Value
The number you read from an instrument: \(25.4\)
Unit
The standard of comparison: \(\text{mL, g, cm, } {^\circ}\text{C}\)
Uncertainty
The range of doubt: \(\pm 0.1\) mL

Accuracy vs. Precision

These two terms are frequently confused, but they describe different qualities of a set of measurements.

Accurate & Precise Accurate, Not Precise Precise, Not Accurate Red dot = true value (bullseye)

Why This Matters on the ACT

The ACT Science section tests your ability to interpret experimental data. Questions often require you to identify which measurements are most reliable, which instruments are more precise, or how uncertainty affects conclusions.

1
Data Representation passages may ask you to read values from graphs and tables with specific precision.
2
Research Summaries may describe instruments with different levels of precision and ask which is better.
3
Conflicting Viewpoints may hinge on whether data is accurate enough to support a conclusion.

Significant Figures: The Core Rule

Significant figures (sig figs) tell you how precisely a measurement was made. More sig figs means a more precise instrument was used.

Ruler A: marked every \(1\) cm
0 1 2 3 4 5 6 7 8 9
Reading: \(3.5\) cm
(2 sig figs)
Ruler B: marked every \(0.1\) cm
2.0 2.5 3.0 3.5
Reading: \(3.15\) cm
(3 sig figs)
More divisions = more significant figures = higher precision

Counting Significant Figures

1
All non-zero digits are significant. Example: \(245\) has 3 sig figs.
2
Zeros between non-zero digits are significant. Example: \(1{,}008\) has 4 sig figs.
3
Leading zeros are NOT significant. Example: \(0.0052\) has only 2 sig figs.
4
Trailing zeros after a decimal point ARE significant. Example: \(3.20\) has 3 sig figs.
5
Trailing zeros without a decimal are ambiguous. Example: \(500\) could be 1, 2, or 3 sig figs.

Key Distinction: A Closer Look

Accuracy Precision
Definition Closeness to true value Closeness of repeated trials
Affected by Systematic error (calibration) Random error (variability)
Improved by Better calibration Better instrument / technique
Measured by Percent error Standard deviation / range
Example Average of trials is \(100.1^\circ\text{C}\) Five trials: \(97.5, 97.6, 97.4, 97.5, 97.6\)

Types of Error

Systematic Error
Consistent, repeatable errors caused by faulty equipment or flawed method. Shifts ALL data in one direction. Affects accuracy.
Random Error
Unpredictable fluctuations in measurements. Scatters data around the true value. Affects precision.

The Percent Error Formula

Percent error quantifies accuracy by comparing a measured value to the accepted (true) value:

Low % Error
Your measured value is close to the true value: high accuracy.
High % Error
Your measured value is far from the true value: low accuracy. Look for systematic error.

How to Apply on the ACT

1
Identify the instrument or method. What tool was used? What is its smallest division?
2
Determine the precision. Count significant figures or note the uncertainty (\(\pm\) value).
3
Check for accuracy. Is a true/accepted value given? Compare using percent error.
4
Compare trials or instruments. Look at the spread (range) for precision and closeness to truth for accuracy.
5
Match your answer to the precision of the data. Don't report more sig figs than the data supports.

Example 1: Reading a Graduated Cylinder

50 40 30 Read at bottom of meniscus
Reading: \(39.7\) mL (3 sig figs)

Example 2: Comparing Two Thermometers

Two thermometers are used to measure the boiling point of water. The accepted value is \(100.0^\circ\text{C}\).

Trial Thermometer A (\(^{\circ}\)C) Thermometer B (\(^{\circ}\)C)
1\(99.8\)\(97.5\)
2\(100.3\)\(97.6\)
3\(99.5\)\(97.4\)
4\(100.1\)\(97.5\)
Average\(99.9\)\(97.5\)

Example 3: Calculating Percent Error

A student measures the density of aluminum as \(2.85 \text{ g/cm}^3\). The accepted value is \(2.70 \text{ g/cm}^3\). What is the percent error?

1
Identify values: Measured = \(2.85\), Accepted = \(2.70\)
2
Find absolute difference: \(|2.85 - 2.70| = 0.15\)
3
Divide by accepted: \(\frac{0.15}{2.70} \approx 0.0556\)
4
Multiply by 100: \(0.0556 \times 100 = \) \(5.56\%\)

Uncertainty and Error Bars

On ACT Science graphs, error bars show the range of uncertainty around each data point. Longer bars mean less precision.

Trial Number Value (g) 5 10 15 20 25 1 2 3 4 Small error bars: precise Large error bars: less precise

Common Mistakes

Confusing Accuracy and Precision
Saying "precise" when you mean "close to the true value." Precision is about consistency, not correctness.
Counting Leading Zeros
Treating \(0.0045\) as having 4 sig figs. Leading zeros are placeholders: it has only 2 sig figs.
Ignoring Error Bars
Treating overlapping error bars as "different." If error bars overlap, the difference may not be significant.

Summary of Key Concepts

Concept What It Measures How to Assess
Accuracy Closeness to true value Percent error
Precision Consistency of trials Range or standard deviation
Significant Figures Precision of instrument Count digits by rules
Systematic Error Bias in one direction Compare to accepted value
Random Error Scatter in data Error bars / range

Question 1 of 5

A student measures a solution's boiling point five times and gets: \(101.2, 101.3, 101.1, 101.2, 101.3\) \(^{\circ}\)C. The accepted value is \(100.0^\circ\text{C}\). These measurements are best described as:

Question 2 of 5

How many significant figures are in the measurement \(0.004070\) g?

Question 3 of 5

A student measures the density of copper as \(9.15 \text{ g/cm}^3\). The accepted density is \(8.96 \text{ g/cm}^3\). What is the percent error?

Question 4 of 5

On a graph, two data points have error bars that overlap significantly. What can you conclude?

Question 5 of 5

A graduated cylinder is marked every \(1\) mL. A student records a volume as \(23\) mL. Which recorded value would demonstrate proper use of significant figures?